상품상세정보

Description

Feather is the new development board from Adafruit and like its namesake it is thin light and lets you fly! We designed Feather to be a new standard for portable microcontroller cores.

This is theAdafruit Feather M0 Bluefruit LE- our take on an 'all-in-one' Arduino-compatible + Bluetooth Low Energy with built in USB and battery charging. Its an Adafruit Feather M0 with a BTLE module ready to rock!We have other boards in the Feather family check'em out here.

Bluetooth Low Energy is the hottest new low-power 2.4GHz spectrum wireless protocol. In particular its the only wireless protocol that you can use with iOS without needing special certification and it's supported by all modern smart phones. This makes it excellent for use in portable projects that will make use of an iOS or Android phone or tablet. It also is supported in Mac OS X and Windows 8+.

At the Feather M0's heart is an ATSAMD21G18 ARM Cortex M0 processor clocked at 48 MHz and at 3.3V logic the same one used in the newArduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much)! This chip comes with built in USB so it has USB-to-Serial program & debug capability built in with no need for an FTDI-like chip.

To make it easy to use for portable projects we added a connector for any of our 3.7V Lithium polymer batteries and built in battery charging. You don't need a battery it will run just fine straight from the micro USB connector. But if you do have a battery you can take it on the go then plug in the USB to recharge. The Feather will automatically switch over to USB power when its available. We also tied the battery thru a divider to an analog pin so you can measure and monitor the battery voltage to detect when you need a recharge.

Here's some handy specs! Like all Feather M0's you get:

• Measures 2.0" x 0.9" x 0.28" (51mm x 23mm x 8mm) without headers soldered in
• Light as a (large?) feather - 5.7 grams
• ATSAMD21G18 @ 48MHz with 3.3V logic/power
• No EEPROM
• 3.3V regulator with 500mA peak current output
• USB native support comes with USB bootloader and serial port debugging
• You also get tons of pins - 20 GPIO pins
• Hardware Serial hardware I2C hardware SPI support
• 8 x PWM pins
• 10 x analog inputs
• 1 x analog output
• Built in 100mA lipoly charger with charging status indicator LED
• Pin #13 red LED for general purpose blinking
• Power/enable pin
• 4 mounting holes
• Reset button

TheFeather M0 Bluefruit LEuses the extra space left over to add our excellent Bluefruit BTLE module + two status indicator LEDs.

The Power of Bluefruit LE

The Bluefruit LE module is an nRF51822 chipset from Nordic programmed with multi-function code that can do quite a lot! For most people they'll be very happy to use the standard Nordic UART RX/TX connection profile. In this profile the Bluefruit acts as a data pipe that can 'transparently' transmit back and forth from your iOS or Android device. You can use ouriOS ApporAndroid App orwrite your own to communicate with the UART service.

The board is capable of much more than just sending strings over the air! Thanks to an easy to learnAT command set you have full control over how the device behaves including the ability to define and manipulate your ownGATT Servicesand Characteristics orchange the way that the device advertises itself for other Bluetooth Low Energy devices to see. You can also use the AT commands to query the die temperature check the battery voltage and more check the connection RSSI or MAC address and tons more. Really way too long to list here!

Use the Bluefruit App to get your project started

Using our BluefruitiOS ApporAndroid App you can quickly get your project prototyped by using your iOS or Android phone/tablet as a controller. We have acolorpicker quaternion/accelerometer/gyro/magnetometer or location (GPS) and an 8-buttoncontrol game pad. This data can be read over BLE and piped into the ATmega32u4 chip for processing & control

You can do a lot more too!

• The Bluefruit can also act like an HID Keyboard(for devices that support BLE HID)
• Can become a BLE Heart Rate Monitor(a standard profile for BLE) - you just need to add the pulse-detection circuitry
• Turn it into a UriBeacon the Google standard for Bluetooth LE beacons. Just power it and the 'Friend will bleep out a URL to any nearby devices with the UriBeacon app installed.
• Built in over-the-air bootloading capability so we can keep you updated with the hottest new firmware.Use any Android or iOS device to get updates and install them. This will update the native code on the BLE module to add new wireless capabilities not program the ATmega chip.

Comes fully assembled and tested with a USB bootloader that lets you quickly use it with the Arduino IDE. We also toss in some header so you can solder it in and plug into a solderless breadboard.Lipoly battery and MicroUSB cable not included(but we do have lots of options in the shop if you'd like!)

Check out our tutorial for all sorts of details including schematics files IDE instructions and more!