상품명 | Adafruit DotStar Digital LED Strip - White 144 LED/m - One Meter [WHITE] |
---|---|
판매가 | 139,818원 |
원산지 | USA |
상품코드 | P000DWWA |
수량 | |
세액 | 13,982원 |
공급사 | Adafruit |
SNS 상품홍보 | |
---|
(최소주문수량 1개 이상 / 최대주문수량 0개 이하)
사이즈 가이드Move over NeoPixels there's a new LED strip in town! These fancy new DotStar LED strips are a great upgrade for people who have loved and used NeoPixel strips for a few years but want something even better. DotStar LEDs use generic 2-wire SPI so you can push data much faster than with the NeoPixel 800 KHz protocol and there's no specific timing required. They also have much higher PWM refresh rates so you can do Persistence-of-Vision (POV) and have less flickering particularly at low brightness levels.
Like NeoPixels DotStar LEDs are 5050-sized LEDs with an embedded microcontrollerinside the LED. You can set the color/brightness of each LED to 24-bit color (8 bits each red green and blue). Each LED acts like a shift register reading incoming color data on the input pins and then shifting the previous color data out on the output pin. By sending a long string of data you can control an infinite number of LEDs just tack on more or cut off unwanted LEDs at the end. The PWM is built into each LED-chip so once you set the color you can stop talking to the strip and it will continue to PWM all the LEDs for you
However unlike NeoPixels these LEDs have 2 wires (input and output) for sending data - one clock pin and one data pin. That means you need two pins not one to control DotStars.Because the clock and data is seperated you can use any processor speed or type to control these strips and you don't have to worry about being careful with the timing. Hardware SPI support is handy but not required. This makes them excellent for use with any microcontroller or microprocessor including Arduino Raspberry Pi BeagleBone Propeller SparkCore and any 'raw' microcontrollers/microprocessors. It's very easy to port the library and you can send data to the pixels at up to 32MHz clock rate!
Another nice thing about DotStars is their high PWM rate. You only have to set the 24-bit color data for each pixel LED once and then the LED+built-in-chip will handle the PWMing of the red green and blue. On NeoPixels this PWM rate happens 400 Hz which works well but is noticably at lower brightnesses and if the strip is moving in any way. DotStars have a 20 KHz PWM rate so even when moving the strip around you won't see the pixelation the color blending is very smooth.
This is a full meter of the 144 LED-per-meter version of our DotStar strips on white flex PCB.We have 30 LED/m 60 LED/m and 144 LED/m on both white and black flex PCB.
The strip is made of flexible PCB material and comes with a weatherproof sheathing. You can cut this stuff pretty easily with wire cutters there are cut-lines every 1 LED. Solder to the 0.1" copper pads and you're good to go. Of course you can also connect strips together to make them longer just watch how much current you need! We have a 5V 4A power supply that can drive a half meter or meter a 5V/10A supply that can drive a couple meters(depending on use)You must use a 5V DC power supply to power these strips do not use higher than 6V or you can destroy the entire strip
This strip comes as a single full meter with a4-pin JST SM connectoron each end. If you buy multiples you will get multiple 1 meter strips they will not come on a continuous strip! To wire up these strips we suggest picking up someJST SMplugandreceptaclecablesfor the signal wiresFor the power wires you will also probably want a 2.1mm DC jack to wire in so you can connect one of our 5V wall adapters to power it.
The manufacturer of the APA102C smart LED used in this strip used to be GRB order and has changed in 2015 to have BRG color order. This means if you are using our DotStar library you'll need to change the initialization to tell it which you are using. Check the tutorial for details on how to do this! The LED colors are otherwise identical you just have to pipe the data to it in a slightly different order.
Technical specs (for the strips):
Technical specs (for the LEDs):
Note:Strips comewith 4 solder points per segment but the arrangement may vary depending on the supplier so please check when soldering/powering!
* 세금계산서 발행방법은 게시판 공지사항 참조.
* 기술문의는 이메일(master@toolparts.co.kr)로 문의.
전자부품 특성상 제품에 이상이 있거나, 상품정보와 상이한 경우 외 에 단순 고객변심으로는
교환 반품이 불가능 합니다 구매전 이점 유의해 주세요!!!
고액결제의 경우 안전을 위해 카드사에서 확인전화를 드릴 수도 있습니다. 확인과정에서 도난 카드의 사용이나 타인 명의의 주문등 정상적인 주문이 아니라고 판단될 경우 임의로 주문을 보류 또는 취소할 수 있습니다.
무통장 입금은 상품 구매 대금은 PC뱅킹, 인터넷뱅킹, 텔레뱅킹 혹은 가까운 은행에서 직접 입금하시면 됩니다.
주문시 입력한 입금자명과 실제입금자의 성명이 반드시 일치하여야 하며, 7일 이내로 입금을 하셔야 하며 입금되지 않은 주문은 자동취소 됩니다.
교환 및 반품이 가능한 경우
- 상품을 공급 받으신 날로부터 7일이내 단, 가전제품의
경우 포장을 개봉하였거나 포장이 훼손되어 상품가치가 상실된 경우에는 교환/반품이 불가능합니다.
- 공급받으신 상품 및 용역의 내용이 표시.광고 내용과
다르거나 다르게 이행된 경우에는 공급받은 날로부터 3월이내, 그사실을 알게 된 날로부터 30일이내
교환 및 반품이 불가능한 경우
- 고객님의 책임 있는 사유로 상품등이 멸실 또는 훼손된 경우. 단, 상품의 내용을 확인하기 위하여
포장 등을 훼손한 경우는 제외
- 포장을 개봉하였거나 포장이 훼손되어 상품가치가 상실된 경우
(예 : 가전제품, 식품, 음반 등, 단 액정화면이 부착된 노트북, LCD모니터, 디지털 카메라 등의 불량화소에
따른 반품/교환은 제조사 기준에 따릅니다.)
- 고객님의 사용 또는 일부 소비에 의하여 상품의 가치가 현저히 감소한 경우 단, 화장품등의 경우 시용제품을
제공한 경우에 한 합니다.
- 시간의 경과에 의하여 재판매가 곤란할 정도로 상품등의 가치가 현저히 감소한 경우
- 복제가 가능한 상품등의 포장을 훼손한 경우
(자세한 내용은 고객만족센터 1:1 E-MAIL상담을 이용해 주시기 바랍니다.)
※ 고객님의 마음이 바뀌어 교환, 반품을 하실 경우 상품반송 비용은 고객님께서 부담하셔야 합니다.
(색상 교환, 사이즈 교환 등 포함)